Metrologic IS4220 ScanGlove Guía de usuario

METROLOGIC INSTRUMENTS, INC.IS4220 ScanGlove®Laser Bar Code ScannerInstallation and User’s Guidemlpn 2348 cover.qxd 9/21/2004 2:57 PM Page 1

6 SIGNAUX OPTIQUES Sur la partie supérieure du scanner se trouvent une diode LED rouge et une diode LED verte. Quand le scanner est sous tension,

7OPTISCHE ANZEIGEN Auf der Oberseite des Scanners befinden sich eine rote und eine grüne Leuchtdiodenanzeige. Ist der Scanner eingeschaltet, so ge

8 SEGNALI OTTICI Sulla parte superiore dello scanner si trovano due diodi luminosi: uno rosso e uno verde. Quando lo scanner è inserito, i diodi

9AUDIBLE INDICATORS The scanner provides sounds to signal certain conditions. To change the volume (four settings are available) or turn the beepe

10 LABELS Each IS4220 has a serial number label and a laser class label on the bottom of the unit. These labels provide important information like

11INFRARED (IR) OBJECT SENSOR An infrared (IR) device located behind the window initiates the scanning process. The IR sensor is active as long as

12 Scan Field The depth of field for the scanner is 12.7 mm to 203 mm (.5" to 8") from the face of the output window for .33 (13 mil) Ba

13SPECIFICATIONS IS4220 SPECIFICATIONS OPERATIONAL Light Source: 650 nm VLD Depth of Field: 12.7 mm to 203 mm (.5" to 8") for .33

14 DEFAULT SETTINGS Many functions of the scanner can be "programmed", that is enabled or disabled. The scanner is shipped from the fact

15DEFAULT SETTINGS PARAMETER DEFAULT RS232 LIGHT PEN KEYBOARD WEDGE USB ACK/NAK  XON/XOFF *  No Intercharacter Delay    1 Milli

16 DEFAULT SETTINGS PARAMETER DEFAULT RS232 LIGHT PEN KEYBOARD WEDGE USB Hong Kong Matrix 2 of 5     Airline 2 of 5     Minimum

17DEFAULT SETTINGS PARAMETER DEFAULT RS232 LIGHT PEN KEYBOARD WEDGE USB ]C1 Transmit Coupon C128     Coupon 128 Group Separator  

18 DEFAULT SETTINGS PARAMETER DEFAULT RS232 LIGHT PEN KEYBOARD WEDGE USB RTS Counter Toggle   Beep on BEL RS232   Bancorner Mode 

19TROUBLESHOOTING GUIDE The following guide is for reference purposes only. Contact a Metrologic representative at 1-800-ID-METRO or 1-800-436-387

20 LIMITED WARRANTY The IS4220 ScanGlove® scanners are manufactured by Metrologic at its Blackwood, New Jersey, U.S.A. facility. The IS4220 scanne

21NOTICES Notice This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules

22 NOTICES European Standard Warning This is a class A product. In a domestic environment this product may cause radio interference in which ca

23PATENTS This METROLOGIC product may be covered by one or more of the following U.S. Patents: U.S. Patent No. 5,260,553; 5,340,971; 5,340,973;

24 INDEX A application ...1 audible...5–9 autodiscriminates ...

25 INDEXR razzberry tone ...9, 14 red LED ...4, 5–9 repair ...

ii LOCATIONS CORPORATE HEADQUARTERS NORTH AMERICA EUROPEAN, MIDDLE EAST & AFRICAN HEADQUARTERS USA, NEW JERSEY GERMANY, MUNICH Metrologic

NOTES

November 2004 Printed in the USA 00 - 02348C

iii TABLE OF CONTENTS Introduction ... 1 Sca

1INTRODUCTION The IS4220 ScanGlove® is a fully automatic single-line laser barcode scanner. It is designed to be used as a “hands-free” wearable

2 SCANNER INSTALLATION 1. Turn off power to the host system. 2. Connect the communication cable to the proper port on the host device. 3. Tu

3SCANNER CONFIGURATION TO THE HOST SYSTEM The IS4220 is shipped from the factory pre-programmed to a set of default parameters. It may be necessa

4 PARTS OF THE SCANNER Figure 1. Scanner Parts Item No. Description  Green LED When a bar code is read successfully the green LED will flash

5VISUAL INDICATORS There is a red and a green LED located on the top of the scanner. When the scanner is on, the flashing or constant illuminatio