Metrologic MS5100 Guía para resolver problemas

6 INSTALLING THE SCANNER TO THE HOST SYSTEM Keyboard Wedge MS5145-47 1. Turn off the PC. 2. Connect the 10-pin RJ45 male connector into the ja

7INSTALLING THE SCANNER TO THE HOST SYSTEM Stand Alone Keyboard MS5145-48 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connect

8 Figure 7. INSTALLING THE SCANNER TO THE HOST SYSTEM USB: LOW SPEED HID/POS USB MS5145-38 FULL SPEED USB MS5145-40 1. Turn off the host sy

9THE POWERLINK CABLE Disconnecting the PowerLink Cable Before removing the cable from the scanner, Metrologic recommends that the power on the h

10 SCANNER PARTS Green & Red LEDs The MS5145’s laser pulses on and off when no bar code is presented, and stays on when it senses a bar code

11THE MS5145 ECLIPSE™ SERIES HOW TO USE CODEGATE AND THE MANUAL ACTIVATION MODE CODEGATE® MANUAL ACTIVATION MODE* * This feature is not a def

12 AUDIBLE INDICATORS When the MS5145 scanner is operational, it provides audible feedback. These sounds indicate the status of the scanner. Eig

13VISUAL INDICATORS There is a red LED and a green LED on the MS5145. When the scanner is on, the activity of the LEDs indicates the status of th

14 FAILURE MODES One Razzberry Tone on Power-up This indicates the scanner has experienced a laser or flipper subsystem failure. Return the unit

15PROGRAMMING MODES The MS5145 Eclipse has 3 modes of programming.  Bar Codes Eclipse can be configured by scanning the bar codes located in th

16 PROGRAMMING MODES 4. During programming, the motor and laser turn off. YOU CANNOT SCAN A BAR CODE WHILE IN SERIAL PROGRAM MODE. 5. There is

17Programming Modes EXAMPLE #3: The following example shows the events that occur when an invalid bar code is sent. This sample will load the fa

18 Upgrading the Flash ROM Firmware The MetroSet2 program is a functional component of Metrologic’s new line of Flash- based scanners. This progra

19SCAN AREA Minimum Bar Code Element Width A B C D E F mm .10 .12 .17 .26 .33 .66 mils 4.1 4.8 6.8 10.4 13 26

20 LABELS Each scanner has one label on the underside of the unit. This label has the model number, date of manufacture, serial number, laser and

21APPLICATIONS AND PROTOCOLS The model number on each scanner includes the scanner number and factory default communications protocol. Scanner Ve

22 TROUBLESHOOTING GUIDE The following guide is for reference purposes only. Contact a Metrologic representative at 1-800-ID-Metro or 1-800-436-38

23TROUBLESHOOTING GUIDE Symptoms Possible Causes Solution The unit powers up, but does not scan and/or beep. The bar code being scanned does not

24 TROUBLESHOOTING GUIDE Symptoms Possible Causes Solution The unit scans but the data is not correct. The unit’s configuration is not correct. M

25RS232 DEMONSTRATION PROGRAM If an RS232 scanner is not communicating with your IBM compatible PC, key in the following BASIC program to test that

ii Locations CORPORATE HEADQUARTERS NORTH AMERICA EUROPEAN, MIDDLE EAST & AFRICAN HEADQUARTERS USA, NEW JERSEY GERMANY, MUNICH Metrolog

26 DESIGN SPECIFICATIONS OPERATIONAL Light Source Visible Laser Diode 650 nm ± 10 nm Laser Power (peak) <1.0 mW Depth of Scan Field (for 13m

27DESIGN SPECIFICATIONS ELECTRICAL Input Voltage 5 VDC ± 0.25 V Power - Operating 675 mW Current - Operating 125 mA Average @ 5 VDC DC Transfo

28 DEFAULT SETTINGS Many functions of the scanner can be “configured” or enabled/disabled. The scanner is shipped from the factory configured to a

29DEFAULT SETTINGS Parameter Default OCIA RS232 Light Pen IBM 46xxKBW USBLaser EmulationMod 43 Check on Code 39        MSI-Ples

30 DEFAULT SETTINGS Parameter Default OCIA RS232 Light Pen IBM 46xxKBW USBLaser EmulationSame symbol rescan timeout: 750 msecs     

31DEFAULT SETTINGS Parameter Default OCIA RS232 Light Pen IBM 46xxKBW USBLaser EmulationTransmit Sanyo ID Characters   Nixdorf ID

32 DEFAULT SETTINGS Parameter Default OCIA RS232 Light Pen IBM 46xxKBW USBLaser Emulation100 msec to Find Supplement Programmable in 100 msec

33SCANNER AND CABLE TERMINATIONS Scanner Pinout Connections MS5145-41 RS232C and Light Pen Emulation Pin Function 1 Ground 2 RS232 Transmit Out

34 SCANNER AND CABLE TERMINATIONS MS5145-9 OCIA Pin Function 1 Ground 2 RS232 Transmit Output 3 RS232 Receive Input 4 RDATA 5 RDATA Return 6 C

35SCANNER AND CABLE TERMINATIONS Cable Connector Configurations (Host End) “Standard” PowerLink Cable 55-55000A-3 Pin Function 1 Shield Ground 2

iii TABLE OF CONTENTS Introduction... 1 Sc

36 SCANNER AND CABLE TERMINATIONS Cable Connector Configuration (Host End) Keyboard Wedge PowerLink Cable 55-55002A-3 Pin Function 1 Keyboard Cl

37LIMITED WARRANTY The MS5145 scanner is manufactured by Metrologic at its Suzhou, China facility. The MS5145 scanners have a two (2) year limited

38 LASER AND PRODUCT SAFETY Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Pa

39LASER AND PRODUCT SAFETY Caution Caution Use of controls or adjustments or performance of procedures other than those specified herein may resu

40 PATENTS Patent Information “This METROLOGIC product may be covered by one or more of the following U.S. Patents: U.S. Patent No.; 5,260,553

41INDEX A AC Input/Outlet...5, 6, 7 Accessories ...2 Adapter...

42 INDEX

January 2006 – Web 01 Only Printed in China 70- 79016B

1 INTRODUCTION The MS5145 Eclipse is a single-line, hand-held laser scanner. Equipped with Metrologic’s patented CodeGate technology, Eclipse ca

2 SCANNER AND ACCESSORIES BASIC KIT Part # Description MS5145 Eclipse Scanner 00-02544 MetroSelect Single-Line Configuration Guide* 70-79016 Ins

3SCANNER AND ACCESSORIES OPTIONAL ACCESSORIES Part # Description 55-55235A-N-3 USB Power/Communication Cable, 1.5 m (5’) straight cord, long strai

4 OPERATIONAL TEST 1. Connect the 10-pin RJ45 male connector into the jack on the Eclipse. You will hear a ‘click’ when the connection is made.

5INSTALLING THE SCANNER TO THE HOST SYSTEM MS5145-00/9/11/14/41 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector into t