Metrologic MS6520 Guía de usuario

METROLOGIC INSTRUMENTS, INC.IS6520/MS6520 Cubit® SeriesOmnidirectional Bar Code ScannerInstallation and User’s Guide

4INSTALLATIONKeyboard Wedge (IS6520-47/MS6520-47)1. Turn off the host device.2. Plug the male 10-pin RJ45 end of thePowerLink cable into the 10-pin

5INSTALLATIONStand Alone Keyboard (IS6520-47/MS6520-47)1. Turn off the host device.2. Plug the male 10-pin RJ45 end of thePowerLink cable into the 1

6DISCONNECTING THE POWERLINK CABLES FROM THE SCANNERBefore removing the cable from the scanner, Metrologic recommends that thepower on the host system

7SCANNER PARTSA. SpeakerServes as an audible indicator.B. Green & Red LEDsDuring normal operation, the greenLED is on. This indicates that thel

8STANDSFixed Vertical Stand (MLPN 46-46145)Optional purchase.a. Fixed Vertical Stand ... Qty. 1b. #7 x 1.00” Wood Screw ... Qty. 3c. M3 x 0.

9AUDIBLE INDICATORSWhen the IS6520/MS6520 scanner is in operation, it provides audible feedback.These sounds indicate the status of the scanner. Eigh

10FAILURE MODESFlashing Green and One Razzberry ToneThis indicates the scanner has experienced a lasersubsystem failure. Return the unit for repair

11VISUAL INDICATORSThere is a red LED and a green LED on IS6520/MS6520. When the scanner ison, the flashing or stationary, activity of the LEDs indic

12PROGRAMMING MODESThe IS6520/MS6520 Cubit has 3 modes of programming.Bar Codes: Cubit can be configured by scanning the bar codes located in theMetr

13PROGRAMMING MODES (CONTINUED)6. To enter serial program mode, send the following command [stx]999999[etx].7. To exit serial program mode, send the

14PROGRAMMING MODES (CONTINUED)EXAMPLE #3: The following example shows the events that occur when aninvalid bar code is sent. This sample will load t

15LABELSEach scanner has a label on the back of the unit that lists the model number,date of manufacture, serial number, CE and caution information.

16OPTIMAL LOW AND CLOSE DEPTH OF FIELDMinimum Bar Code Element WidthABCDE FGHJ Kmm- .15 - .17 - - .25 .33 .53 -mils- 5.7 - 6.8 - - 10 13 21 -Note: Th

17OPTIMAL HIGH AND NORMAL DEPTH OF FIELDMinimum Bar Code Element WidthABCDE FGHJ Kmm- .15 - .17 - - .25 .33 .53 -mils- 5.7 - 6.8 - - 10 13 21 -Note:

18FAR DEPTH OF FIELDMinimum Bar Code Element WidthABCDE FGHJ Kmm- .15 - .17 - - .25 .33 .53 -mils- 5.7 - 6.8 - - 10 13 21 -025507510012515017520025022

19TROUBLESHOOTING GUIDEThe following guide is for reference purposes only. Contact a Metrologicrepresentative at 1-800-ID-METRO or 1-800-436-3876 to

20TROUBLESHOOTING GUIDE (CONTINUED)All InterfacesIS6520/MS6520 Series Troubleshooting Guide (continued)SYMPTOMS POSSIBLE CAUSE(S) SOLUTIONThe unitpowe

21TROUBLESHOOTING GUIDE (CONTINUED)All InterfacesIS6520/MS6520 Series Troubleshooting Guide (continued)SYMPTOMS POSSIBLE CAUSE(S) SOLUTIONScanner beep

22TROUBLESHOOTING GUIDE (CONTINUED)RS232 onlyIS6520/MS6520 Series Troubleshooting Guide (continued)SYMPTOMS POSSIBLE CAUSE(S) SOLUTIONPowers up OKand

23APPENDIX ADesign SpecificationsOperationalLight Source: VLD 650 ± 10 nm, 0.681 milliwatts (PEAK)Depth of Field: 0 mm to 176 mm (0” to 7”) for 0.33 m

iiLOCATIONSCorporate Headquarters North America Metrologic Instruments, Inc. Customer Service: 1-800-ID-METRO90 Coles Road Tel: 856-228-8100Blackwood

24APPENDIX A (CONTINUED)Design SpecificationsElectricalPower: 1.0 WInput Voltage: 5 VDC ± 0.25 VOperating Current: 200 mA typical @5VDCDC Transformers

25APPENDIX BDefault SettingsMany functions of the scanner can be "programmed" - that is, enabled ordisabled. The scanner is shipped from th

26APPENDIX B (CONTINUED)Parameter Default RS232*LightPenKBWDTS/NIXDORF*NCR FNCR SPoll Light Pen Source9Beeper Tone Normal9 9 9Beep/Transmit SequenceBe

27APPENDIX B (CONTINUED)Parameter Default RS232*LightPenKBWTransmit UPC-A Manufacturer ID#*9 9 9Transmit UPC-A Item ID#*9 9 9Transmit Codabar Start/St

28APPENDIX B (CONTINUED)Parameter Default RS232*LightPenKBWMessage RTS/CTS9XON/XOFF Handshaking9ACK/NA K9Two Digit Supplements9as code 399Five Digit S

29110APPENDIX CScanner Pinout ConnectionsThe IS6520/MS6520 scanner interfaces terminateto a 10-pin modular jack. The serial # labelindicates the inter

30APPENDIX C (CONTINUED)Keyboard Wedge Powerlink and Adapter Cable (MLPN 54-54008)The Keyboard Wedge PowerLink cable is terminated with a 5-pin DIN fe

31APPENDIX DWarranty and DisclaimerLimited WarrantyThe IS6520/MS6520 Cubit® scanners are manufactured by Metrologic at itsBlackwood, New Jersey, U.S.A

32APPENDIX ENoticesNoticeThis equipment has been tested and found to comply with limits for a Class A digital device, pursuant toPart 15 of the FCC Ru

33APPENDIX E (CONTINUED)European StandardWarningThis is a class A product. In a domestic environment this product may causeradio interference in whic

iiiTABLE OF CONTENTSIntroduction...1Scanner and Accessori

35APPENDIX F Patents For patent information, please refer to www.honeywellaidc.com/patents.

35INDEXAAC input/outlet...2, 3, 4, 5, 29Accessories...2Approvals ...15, 32, 33Assignmen

36INDEXOOperating current ...24Operating temperture ...24Operation...9, 23, 32Operational.

July 2004Printed in the USA 00 - 02421B

ivTABLE OF CONTENTSAppendix CScanner Pinout Connections ...29Cable Connector Configuration

1INTRODUCTIONMetrologic's Cubit® Series of compact omnidirectional bar code scannersincludes the MS6520 for retail applications and the IS6520 fo

2SCANNER AND ACCESSORIESBASIC KIT COMPONENTSPart No. DescriptionIS6520/MS6520 Cubit® Omnidirectional Scanning Engine00-02421 Installation and User’s G

3INSTALLATIONRS232, Light Pen (IS6520-41/MS6520-41)1. Turn off the host device.2. Plug the male 10-pin RJ45 end of thePowerLink cable into the 10-pi