Metrologic IS1000 Series Guía de usuario Pagina 181
- Pagina / 198
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix
I
Barcode
Setting
175
Test Mode
The reader is always scanning and will decode repeatedly even with the
same barcode.
Momentary Mode
The reader will be scanning as long as the switch is pressed.
Alternate Mode
The reader will start scanning once the switch is triggered. It will
continue scanning until the scan trigger is pressed again.
Aiming Mode
This mode is used when two barcodes are printed too close to each other.
By selecting this mode, the user needs to trigger twice to decode.
That is, the first trigger is for aiming only, while the second trigger will
truly start to decode. After the first trigger, the scanner will keep on
scanning for 1 second so that the user may take aim. But the user must
press the second trigger within this period (1 second by default);
otherwise, it will be reset and the user has to take aim again.
The scanning goes on until one of the following events happens.
a barcode is read
time out (preset scanning period expires)
Laser Mode
This scan mode is most often used on laser scanners. The reader will start
scanning once the scan trigger is pressed.
The scanning goes on until one of the following events happens.
a barcode is read
the scan trigger is released
time out (preset scanning period expires)
Read Redundancy
This parameter is used to specify the level of reading security. The user must compromise
between reading security and decoding speed.
No Redundancy
If "No Redundancy" is selected, one successfully decoded barcode will
make the reading valid and induce the "READER Event".
One times
Two times
Three times
If "Three Times" is selected, it will take a total of four consecutive
successful decodings of the same barcode to make the reading valid.
The higher the reading security is (that is, the more redundancy the user
selects), the slower the reading speed gets.
- BASIC Compiler 1
- Copyright Notice 2
- Contents 3
- Introduction 7
- Typographical Conventions 8
- Revision History 8
- Development Environment 9
- 2.2 System Requirements 10
- 2.3 BASIC Run-time Engine 11
- 2.4 Development Flow 11
- Using The BASIC Compiler 14
- 3.2 Edit Menu 15
- 3.3 Configure Menu 17
- 3.4 Compile Menu 18
- 3.5 Help Menu 19
- Basics of the BASIC Language 21
- 4.2 Variables 22
- 4.3 Expression and Operators 23
- 4.3.2 Arithmetic Operator 24
- 4.3.3 Relational Operator 24
- 4.3.4 Logical Operator 24
- 4.4 Operator Precedence 25
- 4.5 Labels 25
- 4.6 Subroutines 26
- 4.7 Programming Style 27
- BASIC Commands 28
- In This Chapter 29
- 5.1 General Commands 30
- 5.2 Commands for Decision 33
- Structures 33
- 5.4.1 Combining Strings 38
- 5.4.2 Comparing Strings 38
- 5.4.4 Searching for Strings 39
- 5.4.6 Converting for Strings 43
- 5.5.1 Event Triggers 47
- 5.5.2 Lock and Unlock 56
- 5.6 System Commands 58
- 5.7 Barcode Reader Commands 64
- 5.9 Keyboard Wedge Commands 73
- 5.9.2 KBD / Terminal Type 74
- 5.9.5 Alphabets Case 75
- 5.9.6 Digits Position 76
- 5.9.8 Digit Transmission 76
- 5.9.9 Inter-Character Delay 76
- 5.10 Buzzer Commands 80
- 5.13 LED Command 84
- 5.14 Keypad Commands 85
- 5.15 LCD Commands 89
- 5.16 Battery Commands 100
- 5.17 Communication Ports 102
- 5.18 RF Communications 109
- IDs and Groups 111
- 433 MHz RF System 111
- 2.4 GHz RF System 111
- RF Practice 117
- 5.18.4 RF Base Properties 118
- 5.19 Wireless Communications 125
- Net Status 129
- 5.19.3 IEEE 802.11b 131
- TCP/IP Networking 132
- TCP/IP Practice 139
- 5.19.4 Bluetooth 142
- Frequent Device List 145
- Example code (2): 147
- Bluetooth Practice 148
- PAN Application 149
- Keyboard Emulator 149
- 5.20 File Manipulation 151
- 5.20.1 DAT Files 152
- 5.20.3 Error Code 165
- 5.21 Memory 166
- 5.22 Debugging Commands 168
- 5.23 Reserved Host Commands 171
- Barcode Setting 175
- Symbology Parameters 176
- Codabar 177
- EAN13 & UPCA 178
- Plessey 178
- Telepen 179
- RSS14 Limited 179
- Scanner Parameters 180
- Read Redundancy 181
- Time-Out 182
- Negative Barcode 182
- Run-Time Error Table 183
- Debugging Messages 185
Relacionado con productos y manuales para Lectores De Códigos De Barras Metrologic IS1000 Series
(52 paginas)
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.112 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales